Guest Post: Make Your Own Bra Pressing Curve

I love making up sewing tools. There are times a tweezer works better than a bone folder, and a rubber hammer works better than an iron. I have a pencil that works great for spaghetti straps and probably do “wet finger” pressing on silk more times than I care to admit.

It’s really fun and easy to make your own pressing tools, and this week I’m pleased to share a guest tutorial on making your own bra pressing curve from my fellow lingerie-making addict Maddie Flanigan! You may know her from her blog Madalynne, gorgeous sewing photography and brand-new bra making workshops in her Philly studio. So let me step aside as Maddie brings on the drill…

——–

Make Your Own Bra Pressing Curve | Cloth Habit

Based on a similar item sold at Bra-makers Supply, my bra pressing curve has become a
valuable tool. I first came across it when Beverly Johnson mentioned it during her class
on Craftsy. She said it was easy to make and she was right. All it took was a trip to the
hardware store and about 30 minutes. I use it mostly to press cross cup seams without
touching other parts of the bra.

Supplies:
All supplies except for round ball can be sourced at most hardware stores such as Home
Depot and Lowes.

  • Power drill
  • 3″ wood round ball
  • 5.5″ x 5.5″ wood square
  • 1 1/4″ diameter wood dowel
  • Dowel center pins
  • Brad point or dowelling drill bit
  • Just like bra making, sourcing all those little bits can be intimidating. To make it easier, you can buy a dowel kit such as this one.
  • Regular drill bit
  • Pencil
  • Masking or painters tape
  • Wood glue

Make a Bra Pressing Curve | Cloth Habit

Prep: Most likely, your hardware store will sell long, rectangular pieces of wood, not one that is exactly 5.5″ x 5.5″. The same goes for dowels. Having it cut down isn’t a hassle. The hardware store should do it for free. Ask to have extras pieces cut so you have a spare in case you mess up.

Step 1: Using a pencil, mark the center of the sphere, the center of the dowel at the top and bottom, and the center of the square at the top and bottom as well. Mark all of these points with a cross mark.

Make a Bra Pressing Curve | Cloth Habit

Make a Bra Pressing Curve | Cloth Habit

Step 2: Mark the center of the dowel pin and then place it next to the drill bit as shown. Using masking or painters tape, wrap the drill bit at the point where the center point is on the dowel pin. Why? Because you don’t want to drill too far into the ball or the dowel.

Make a Bra Pressing Curve | Cloth Habit

Make a Bra Pressing Curve | Cloth Habit

Step 3: Use power drill to drill a hole into the ball and the dowel at both top and bottom. To ensure that you drill straight down, use a quick grip clamp or have someone hold the ball and the dowel while you drill.

Make a Bra Pressing Curve | Cloth Habit

Step 4: Connect the ball with the dowel by placing a thin coat of wood glue on the dowel pin and inserting one end into the ball and the other into one end of the dowel.

Make a Bra Pressing Curve | Cloth Habit

Step 5: The final step is to connect the dowel/sphere (which is now one) to the wood square. Using a regular drill bit, drill from the bottom of the square block up through the bottom of the down with a regular screw.

Make a Bra Pressing Curve | Cloth Habit

Make a Bra Pressing Curve | Cloth Habit

12 comments

  1. David Coffin says:

    Neat! I can see other uses for such a thing, and I do love all my wooden pressing tools…but did I miss a link to wooden ball sources? As you suggest, I’ve not seen anything like that at my hardware store. Thanks! Also, I bet I’m not the only lazy reader thinking that the ball would probably be almost as useful a pressing aid without any stand!

  2. Amy says:

    Just a thought… I wonder if anyone has tried steaming/shaping their own molded bra cups either with foam or fabric. I think this is one of the techniques that is demonstrated on this tool in the Bra-makers Manual. I don’t usually make molded foam bras but I wonder if others have tried it or are interested in that?

    • Nia says:

      Hi Amy,

      I am surprised no-one replied to you.
      I have not tried this – yet, but I did read somewhere that you can do this with your iron. I would imaging you would be using just the steam, not the actual sole plate since you don’t want to melt or compress the foam. Similar to molding shoulder pads, is my guess.

      I really should to a test with my seam roll and report back.

      But you have me convinced that seamed cups are the way to go, so I don’t want to use any of my foam for anything else 🙂

      • Amy says:

        Hi Nia, I had comments turned off for awhile so this might be why there weren’t responses. 🙂 Sounds like a fun experiment!

Comments are closed.